Product Data Sheet Show all documents
Sika® Injection-101 RC

Sika® Injection-101 RC

Flexible PUR-Injection foam for temporary waterstopping

Sika® Injection-101 RC is a low viscous, fast foaming and solvent-free water-reactive polyurethane injection foam resin, which cures to a dense flexible foam with a fine cellular structure.

  • No reaction takes place unless it is in direct contact with water.
  • Sika® Injection-101 RC can be injected as a single component system.
  • The free foaming expansion in contact with water is up to 40 times.
  • The reaction speed (foam formation) is influenced by the temperatures of the mixed material, the structure and the contact water, plus the hydrodynamic conditions.
  • In cold temperatures (< + 10°C) Sika® Injection-101 RC can be accelerated using Sika® Injection-AC10.
Product Data Sheet Show all documents

Usage

  • Sika® Injection-101 RC is used for the temporary waterstopping of high water intrusions in cracks, joints and cavities in concrete, brickwork and natural stonework.
  • To achieve permanent watertight crack sealing, Sika® Injection-201 CE or Sika® Injection-203 should be injected subsequently.
 

Advantages

  • No reaction takes place unless it is in direct contact with water.
  • Sika® Injection-101 RC can be injected as a single component system.
  • The free foaming expansion in contact with water is up to 40 times.
  • The reaction speed (foam formation) is influenced by the temperatures of the mixed material, the structure and the contact water, plus the hydrodynamic conditions.
  • In cold temperatures (< + 10°C) Sika® Injection-101 RC can be accelerated using Sika® Injection-AC10.

Packaging

Part A10 kg
Part B

12.5 kg

Total22.5 kg

Colour

Part AColourless
Part BBrown

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

German KTW drinking water certificate
German ZTV-ING chapter 3, part 5 (RISS) tested (BASt listed)
Product Information

Chemical Base

Water reactive 2-part polyurethane resin, solvent and CFC free

Shelf Life

24 months shelf life from date of production if stored properly in undamaged, unopened, original sealed packaging.

Storage Conditions

Dry storage at temperatures from +5 °C up to +35 °C. Protect from direct sunlight and humidity.

Density

Part A~1.0 kg/l
Part B~1.25 kg/l

at 20 °C

Viscosity

Part A

~140 mPa∙s

Part B

~155 mPa∙s

at 20 °C
Technical Information

Expansion

Expansion start~15 s after contact with water
Expansion end~67 s

at 20 °C

Application

Application Information

Mixing Ratio

part A:part B =  1:1 by volume

Reaction time table Sika® Injection-101 RC
[PM 10081-11]

0 % Sika® Injection-AC10 1
Material temperature

Expansion start

Expansion end

+5 °C~19 sec~79 sec

+10 °C

~17 sec

~88 sec

+20 °C

~16 sec

~70 sec

5 % Sika® Injection-AC10 1
Material temperatureExpansion start

Expansion end

+5 °C~12 s~57 s
+10 °C~11 s~49 s

+20 °C

~10 s~39 s

10 % Sika® Injection-AC10 1

Material temperature

Expansion start

Expansion end

+5 °C~9 s~41 s

+10 °C

~8 s

~37 s

+20 °C

~7 s

~35 s

1  Dosage of Sika® Injection-AC10 in % by weight of Sika® Injection-101 RC (comp. A+B)

 The given data are laboratory parameters and may deviate depending on the object and conditions on site.

Ambient Air Temperature

+5 °C min. / +35 °C max.

Substrate Temperature

+5 °C min. / +35 °C max.

Pot Life

~2 hours (at + 20 °C)

(ISO 9514)

remove skin from the surface (do not mix in!)
Application steps

MIXING

Empty parts A and B into a mixing vessel and mix slowly and thoroughly for at least 3 min (max. 250 rpm) until homogeneous, thereby observing the safety precautions. The containers are supplied according to the required mixing ratio of 1 : 1 parts by volume.
Partial quantities can be measured out in separate vessels. After mixing, pour the material into the pump’s feed container, stir briefly and apply within the pot life.
After mixing, pour the material into the pump’s feed container, stir briefly and use within the pot life.

If the substrate and/or ambient temperatures are < +10 °C, Sika® Injection-AC10 can be added to Sika® Injection-101 RC to accelerate the start of expansion.

CLEANING OF TOOLS

Clean all tools and application equipment according to the Product Data Sheet for the Sika®Injection Cleaning System.

 

Documents