Product Data Sheet Show all documents

SikaTile®-330 Regular Tile Adhesive

C1-type cement-based tile adhesive for interior floors and walls, and exterior floor installations.

SikaTile® 330 Regular Tile Adhesive is a cement-based adhesive that complies with PNS ISO
13007:2014 Type C1 standards. It is specially formulated for installing both porous tiles such as
ceramic, mosaic, terracotta, and baked clay; and low-porous tiles, including glazed ceramic.

Bond Strength (≥ 0.5 MPa)
Easy to use; simply mix with water. Non-toxic, non-flammable. Cost effective.
Product Data Sheet Show all documents

Usage

SikaTile® 330 Regular Tile Adhesive is a quality, cement-based adhesive for thick or thin bed (TTB) applications, designed for interior floors and walls as well as exterior floor installations.
SikaTile® 330 Regular Tile Adhesive is suitable for laying tiles on a variety of substrates, including concrete, cement render, block work, and rendered brickwork surfaces.  

Advantages

Bond Strength (≥ 0.5 MPa)
Easy to use; simply mix with water. Non-toxic, non-flammable. Cost effective.

Packaging

25 kg per bag

Colour

Gray powder

Product Details

Product Information

Chemical Base

Cement, selected aggregates and additives

Shelf Life

12 months from date of production if stored properly

Storage Conditions

Store properly in unopened and undamaged original sealed containers protected from direct sunlight and moisture.
Technical Information

Mortar mix design

22% - 24% water-to-powder ratio

Tensile Adhesion Strength

Days     MPa       PSI
28         ≥ 0.5       ≥ 73
(product applied using 24% water-to-powder ratio)

Application

Application Information

Mixing Ratio

5.5 to 6 liters of water per 25 kg bag, until a lump free, creamy consistency is achieved.
Working Temperature: 10°C to 35°C.

 

Pot Life

1 – 2 hours

Open Time

20 minutes

Curing Time

24 hours

Fresh mortar density

1.5 – 1.8 kg/ L
Consumption

Consumption

6mm x 6mm notched trowel – approx. 3.5 kg per sqm.

10mm x 10mm notched trowel – approx. 5 kg per sqm.

*Disclaimer: Consumption may be higher depending on surface irregularities. Consult Sika Technical team for further application information
Application steps

MIXING

Add (1) 25kg bag of SikaTile® 330 Regular Tile Adhesive to approximately 5.5 to 6 liters of clean wa-ter, mixing continuously until a lump-free, creamy consistency is achieved.

APPLICATION

Prepare the adhesive as instructed. Allow the mix to stand for 1 to 2 minutes, then remix before use. Spread adhesive onto the substrate using: 6mm x 6mm notched trowel for wall tiling.10mm x 10mm notched trowel for floor tiling. Trowel size depends on tile size, depth of knobs, grooves, or ridges on tile back, substrate evenness. For tiles with deep grooves or ridges (e.g., slate or lugged tiles), butter coat adhesive on the back of the tile in addition to notched trowel application. Thicker adhe-sive beds help compensate for uneven substrates, especially slates. Do not spread more than 1 sqm of adhesive at a time. Ensure adhesive remains wet when tiles are laid and tapped into position for full contact. Ensure no voids under tiles. Do not allow adhesive to skin over before tiling. Install tiles within the open time specified. Do not disturb or walk on tiles for 24 hours after installation. Grout-ing should preferably be carried out at least 24 hours after the completion of tiling. For best results use SikaTile® Grout.

 

CLEANING OF TOOLS

Clean all tools and application equipment with water immediately after use. Hardened or cured materials can be only mechanically removed.

Documents